AAA Battery Holder Tray — 24-Cell 4×6 Array
A tray that holds 24 AAA batteries upright and organized in a 4×6 grid, for bulk battery storage sized exactly to AAA's own diameter rather than a generic multi-size battery organizer.
✓ Full requirement coverage✓ Digitally validated
Key dimensions
| X | 93 mm |
| Y | 62 mm |
| Z | 28 mm |
About this model
AAA is one of the most common household battery sizes, and bulk battery storage is a well-established real need (the same pattern already confirmed with direct listing evidence for AA, C, and D cells). This asset applies the same pattern at AAA's own diameter; unlike the AA/C/D holders, no specific Etsy listing with fixed-count presets was found for AAA specifically in this batch's research, so the demand-gap evidence here is weaker (a reasonable general pattern, not a confirmed specific gap) -- see ops/batches/002.yaml.
Fit notes
- 10.5mm cell diameter (IEC R03/AAA nominal) plus 1mm clearance
- 25mm pocket depth (~56% of a 44.5mm AAA cell) -- stabilizing, not full-length enclosure
- 4×6 layout (24 cells), a round bulk-storage count
Printing & use notes
No print settings (layer height, infill, supports) are specified for this model — use standard settings for your printer and material. See the validation section below for what has and hasn't been checked.
Validation
Requirement coverage
Full — this model covers the stated requirement completely.
LOW RISK Low risk — simple geometry, loose clearances, not load-bearing.
Digitally validated
- ✓ Geometry valid
- ✓ Matches stated dimensions/spec
- ✓ Manifold (watertight)
- ✓ Slicer compatible
- External manufacturing preflight: not checked
Physical fit and print performance
Physical fit and material/printer-specific performance are not independently guaranteed unless explicitly stated. Physical validation status for this object: not yet physically tested.
MyMakerPilot does not guarantee shrinkage, warping, layer adhesion, strength, real-world load bearing, printer-specific tolerance, or first-print functional usability. Physical printing is optional calibration/sampling, not a publishing requirement.
Technical details
Internal provenance and file references, for anyone who wants the full picture.
- Object ID
- battery-holder-aaa-array
- Category
- holders
- Risk classification
- low
- External preflight
- unknown
- Physical validation
- unknown
- Production cost
- unknown
- Human review time
- unknown
- STL file
- /objects/battery-holder-aaa-array/model.stl
- STEP file
- /objects/battery-holder-aaa-array/model.step
Similar objects
AA Battery Holder Tray — 30-Cell 5×6 Array
A tray that holds 30 AA batteries upright and organized in a 5×6 grid, for bulk battery storage in a count that doesn't match the fixed 16/20/25-count presets sold as ready-made holders.
117×97.5×33mm
C Battery Holder Tray — 15-Cell 3×5 Array
A tray that holds 15 C-cell batteries upright and organized in a 3×5 grid, for bulk battery storage in a count that doesn't match the fixed 8/12-count presets sold as ready-made holders.
156×93.6×33mm
D Battery Holder Tray — 10-Cell 2×5 Array
A tray that holds 10 D-cell batteries upright and organized in a 2×5 grid, for bulk battery storage in a count that doesn't match the fixed 8/12-count presets sold as ready-made holders.
196×78.4×38mm
Chapstick & Lip Balm Holder — 16-Tube 4×4 Tray
A tray that holds 16 chapstick or lip balm tubes upright and organized in a 4×4 grid, in a count between the 10-tube and 64-tube products sold as ready-made organizers.
108×108×38mm